Tie-down Vector Dynamics System with PVC Pipe Adapter Manuel d'utilisateur télécharger pdf (Page 1)

2. SET BLOCKS (OR PIERS) ON

VECTOR FOUNDATION PADS

Center the foundation blocks over the Vector

pads.

3. INSIDE CONNECTIONS

Insert 1/2" carriage bolt into square hole on top

ﬂang e of the PVC adaptor. Place the sw ivel

connector bracket that is attached to one end of

the 1-1/4" galvanized strap and thread 1/2" hex

nut onto carriage bolt (ﬁnger tight). Insert 4"

PVC schedule 40 pipe into PVC pipe adaptor and

insert over inside long U-bolt (through slotted

holes). Attach 3/8" hex nuts to u-bolt and ﬁnger

tighten. Repeat the procedure to opposite side of

PVC pipe.

4. TIGHTEN INSIDE HARDWARE

Tighten all previously ﬁnger tightened

hex nuts (1/2" carriage bolts & 3/8"

inside U-bolts).

6. TENSIONING - VECTOR STRAPS

Pull strap past slotted bolt. Cut strap 10

- 12 inches past bolt, insert the strap into

the slotted bolt until ﬂush with opposite

side of bolt. Wind strap a minimum of

four or ﬁve (5) complete revolutions

around the bolt. Continue tightening the

slotted tension bolt until all slack has

been removed and the galvanized strap is

tight.

Set-Up Instructions for the

Vector Dynamics Foundation System with PVC adapter

5. OUTSIDE TENSION BRACKETS

Attach an outside tension bracket on the

outside of the foundation blocks and

Vector pads as shown on right.

Tip:

Place a 3/8" nut on each

U-bolt to keep it in place

while you position the

Vector pads.

TIP:

After centering 1st block(s)

over Vector pads, place

wood cap on top of ﬁrst

block and use hydraulic jack

between pad and I-beam to

force pads into the ground.

Higher pier sets may require

extra block prior to using

hydraulic jack.

Position 1st block(s)

on pad as shown.

LSD/Vector

Combination

Shown

Long

U-bolt

. SET VECTOR FOUNDATION PADS

Clear all organic matter and loose vegetation from the immediate area where the Vector foundation pads will rest. Place a long U-bolt on

the Vector pads as shown. Press or hammer pads into the ground. Vector pads are placed parallel and centered under I-beam.

040403,130

1 2

Résumé du contenu

Page 1 - Set-Up Instructions for the

2. SET BLOCKS (OR PIERS) ON VECTOR FOUNDATION PADSCenter the foundation blocks over the Vectorpads.3. INSIDE CONNECTIONSI

Page 2 - 040403,130

Longitudinal Stabilizer DevicesAs an alternate to installing longitudinal anchors and stabilizer plates, the installer may use longitudinalstabilizin

Commentaires sur ces manuels

Pas de commentaire

Tie-down Vector Dynamics System with PVC Pipe Adapter Manuel d'utilisateur Page 1

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Tie-down Vector Dynamics System with PVC Pipe Adapter. Tie Down Vector Dynamics System with PVC Pipe Adapter User Manual [fr] [de] Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Tie-down Vector Dynamics System with PVC Pipe Adapter Manuel d'utilisateur Page 1

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Tie-down Vector Dynamics System with PVC Pipe Adapter. Tie Down Vector Dynamics System with PVC Pipe Adapter User Manual [fr] [de] Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Tie-down Vector Dynamics System with PVC Pipe Adapter